- 您现在的位置：买卖IC网 > Sheet目录315 > BD7844AEFV-E2 (Rohm Semiconductor)IC LED DISPLAY DVR 5V 28-HTSSOP
BD7844AEFV
Datasheet
● Operational Notes
1. Absolute Maximum Ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc.,
can break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If
any special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical
safety measures including the use of fuses, etc.
2.
3.
4.
5.
6.
7.
8.
9.
Power supply and ground line
Design PCB pattern to provide low impedance for the wiring between the power supply and the ground lines. Pay
attention to the interference by common impedance of layout pattern when there are plural power supplies and ground
lines. Especially, when there are ground pattern for small signal and ground pattern for large current included the
external circuits, please separate each ground pattern. Furthermore, for all power supply pins to ICs, mount a capacitor
between the power supply and the ground pin. At the same time, in order to use a capacitor, thoroughly check to be
sure the characteristics of the capacitor to be used present no problem including the occurrence of capacity dropout at
a low temperature, thus determining the constant.
Ground voltage
Make setting of the potential of the ground pin so that it will be maintained at the minimum in any operating state.
Furthermore, check to be sure no pins are at a potential lower than the ground voltage including an actual electric
transient.
Short circuit between pins and erroneous mounting
In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting
can break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between pins or between
the pin and the power supply or the ground pin, the ICs can break down.
Operation in strong electromagnetic field
Be noted that using ICs in the strong electromagnetic field can malfunction them.
Input pins
In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the
parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of
the input pin. Therefore, pay thorough attention not to handle the input pins, such as to apply to the input pins a voltage
lower than the ground respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage to
the input pins when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is
applied, apply to the input pins a voltage lower than the power supply voltage or within the guaranteed value of
electrical characteristics.
External capacitor
In order to use a ceramic capacitor as the external capacitor, determine the constant with consideration given to a
degradation in the nominal capacitance due to DC bias and changes in the capacitance due to temperature, etc.
Thermal shutdown circuit (TSD)
This LSI builds in a thermal shutdown (TSD) circuit. When junction temperatures become detection temperature or
higher, the thermal shutdown circuit operates and turns a switch OFF. The thermal shutdown circuit, which is aimed at
isolating the LSI from thermal runaway as much as possible, is not aimed at the protection or guarantee of the LSI.
Therefore, do not continuously use the LSI with this circuit operating or use the LSI assuming its operation.
Thermal design
Perform thermal design in which there are adequate margins by taking into account the permissible dissipation (Pd) in
actual states of use.
10. About the pin for the test, the un-use pin
Prevent a problem from being in the pin for the test and the un-use pin under the state of actual use. Please refer to
this Datasheet. And, as for the pin that doesn't specially have an explanation, ask our company person in charge.
11. About the rush current
For ICs with more than one power supply, it is possible that rush current may flow instantaneously due to the internal
powering sequence and delays. Therefore, give special consideration to power coupling capacitance, power wiring,
width of ground wiring, and routing of wiring.
Status of this document
The Japanese version of this document is formal specification. A customer may use this translation version only for a reference
to help reading the formal version.
If there are any differences in translation version of this document formal version takes priority.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
12/14
TSZ02201-0G3G0CZ00310-1-2
15.Oct.2012 Rev.001
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
BD8105FV-E2
IC LED DVR SERIAL PAR 20-SSOP
BD8112EFV-ME2
IC LED DRIVER 24-VSSOP
BD8119FM-ME2
IC WHITE LED DVR PWM 28-HSOP
BD82103GWL-E2
IC LED DRVR WHITE BCKLGT 11-UCSP
BD9206EFV-E2
IC LED DRIVER 6V LCD 20HTSSOP
BD9207FPS-E2
IC LED DVR STEPDWN 1.5A TO252S-5
BH-14E_TI-20T_CTI
ADAPTER PIN CONVERTER 14-20 PIN
BH-20E_CTI-60T_TI
ADAPTER PIN CONVERTER 20-60 PIN
相关代理商/技术参数
BD785
制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:ON Semiconductor 功能描述:
BD7851FP
制造商:ROHM 制造商全称:Rohm 功能描述:Serial / Parallel 4-input Drivers
BD7851FP-E2
功能描述:功率驱动器IC SERIAL IN/PARALLEL OUT DRIVER RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
BD786
制造商:未知厂家 制造商全称:未知厂家 功能描述:TRANSISTOR | BJT | DARLINGTON | PNP | 45V V(BR)CEO | 4A I(C) | TO-127VAR
BD7861KN-E2
制造商:ROHM 制造商全称:Rohm 功能描述:Mixer & Selector IC with PCM CODEC and 16bit D/A Converter
BD787
功能描述:两极晶体管 - BJT 4A 60V 15W NPN RoHS:否 制造商:STMicroelectronics 配置: 晶体管极性:PNP 集电极—基极电压 VCBO: 集电极—发射极最大电压 VCEO:- 40 V 发射极 - 基极电压 VEBO:- 6 V 集电极—射极饱和电压: 最大直流电集电极电流: 增益带宽产品fT: 直流集电极/Base Gain hfe Min:100 A 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PowerFLAT 2 x 2
BD787/D
制造商:未知厂家 制造商全称:未知厂家 功能描述:Complementary Plastic Silicon Power Transistors
BD787_06
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Complementary Plastic Silicon Power Transistors
